Tools You Need to Set Up a New Bathtub
Tools You Need to Set Up a New Bathtub
Blog Article
On this page below you will discover a bunch of superb news on the subject of A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have currently acquired a brand-new tub and don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material checklist ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
As a reader on Tools You Need to Install a New Bathtub , I think sharing that piece of writing was really helpful. Enjoyed our blog entry? Please share it. Let others locate it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request An Appointment
Report this page